Clipper C13SPM Especificaciones

OWNERS MANUAL MEDIUM CONCRETE SAWS MODELS: C13SPM C13SPE C20SPE FORM C20SP 3-2005

10B. Engine Prior to attempting to operate the engine, read the information contained in the engine owner's manual. An engine owners manual is

11 • Use Only Water In The Water Tank • Do Not Drink From The Tank D. Operating The Saw 1. For the engine starting instructions see the Engin

1211. For Self-propelled models move the Transmission Engage/Disengage lever by fully to the Engage position and \ then slowly push the Speed Control

13Additional Guide Lines For Sawing: • Understand and follow all of the instruction in this owners manual. • If wet cutting, turn on the water su

14A. Engine Follow the below schedule for engine maintenance. NOTE: Check the Honda Engine manual that came with the engine for any changes to the

15 Always refer to the engine manual for more detailed information on checking the oil, changing oil, and oil capacity, air filter changes, and fuel

16B. Bearings Re lubrication type bearings must be relubricated daily to assure long life. The grease used should conform to the NLGI grade two con

17III. MAINTENANCE C. V-Belts Warning: Never make adjustments to belts or pulleys while engine is running! 1. The best tension for a belt drive i

18III. MAINTENANCE D. Depth Control The depth control (raising screw) consists of a threaded rod which feeds into a brass nut . In order to keep th

19F. Self-Propelling Operations 1. Speed Control Lever: The operators right hand lever is the speed control lever. Pushing the lever slowly forwar

2WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of s

202. Remove the operators Right hand side blade nut (NOTE: Left hand thread) and Loose Collar. 2. Remove the blade from the saw if installed. 3.

21IV. PARTS LIST SECTION A. Ordering Information 1. List model number and serial number of machine. 2. List part number and serial number of part

B: Service Parts C13SP & C20SP Common

C13SP

C20SPE

Item Model Part No UPC # Description 1 All 83925 Upper Frame 2 All 83926 Board plate 3 All 83927 Upper closing plate 4 All 83928 Und

48 All 83945 Depth lock wheel 49 All 83946 Shaft 50 All 72279 70184655806 Wrench 17mm 51 All 70807 70184655735 Wrench 19mm 52 All 82910 7018

92 All 84067 Waste oil hose 93 All 73862 Fan

NOTES

3CONTENTS PAGE I. Preparation A. Safety Precautions 4-6B. Assembly 7C. Engine Specifications 8D. Pointer Alignment 9 II. Operation A. Blade Ins

Norton Construction Products PO Box 2898 Gainesville, GA 30503 Phone: 800-554-8003 or 770-967-3954 (8:00 A.M. to 7:00 P.M. Eastern Time) Fax: 800-443

4I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extr

5 Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing c

61. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previo

7I. PREPARATION B. Assembly The self-propelled concrete saws are shipped completely assembled and ready for use except for diamond blade, gasoline,

8C. C13SP/C13SPE/C20SPE Concrete Saw Specifications Dimensions/Weight C13SPM C13SPE C20SPE Length (Transport) 56 inch (1142 mm) 56 inch (1142 mm)

9 II. OPERATION Read and understand this manual before running or using the machine! A. Installing the Blade 1. Disconnect the spark plug and the